What is DFM, Really?


Reading time ( words)

Okay, so what is DFM, really? The term "design for manufacturability" has been used for many years now, but does everyone really understand this concept?

For instance, do you design for 10%? Do you design for a specific manufacturer’s capabilities, therefore making you less likely to seek alternative fabricators? How are your drawings worded?

In this article, I will be discussing the reality of DFM and what benefits you, the end-user, by embracing these practices.

Why Design For Manufacturability at All?

Good question. Even if you only buy your boards from a single source--if you have qualified the company already and feel you can expect certain press parameters and dielectric constants based on what they have provided you--it is STILL a good idea to at least design with some latitude. If your design is .1 mm lines and spaces there is not a whole lot of room to either expand or decrease the traces to achieve certain impedances. Clearly, when you have to ingress and egress out of tight-pitch components and your design takes you down to .003”/.003” there is NO ROOM at all for an etch compensation, so you are typically quoted by manufacturers as quarter-ounce foil start. This foil is so thin that we need not compensate for a loss at the etcher like the other copper weights.

Again, as I have mentioned before in my columns, the general rule of thumb is that for every half-ounce of starting copper, you give all the metal features an etch compensation of half a mil. Asking for 1 oz. starting copper, for instance, with 0.003”/0.003” will normally be a no-bid as fabricators would be hard-pressed to be able to run with .002” spaces at Image prior to etch. (Attempting to compensate the 0.003” traces for 1 oz. copper with 1 mil will result in 0.002” spaces at Image prior to etch.) So, 0.003”/0.003” is usually the limit.

Read the full article here.


Editor's Note: This article originally appeared in the May 2014 issue of The PCB Design Magazine.

Share




Suggested Items

Physics, Electrical Engineering, and PCB Design

12/09/2022 | Tamara Jovanovic, Happiest Baby
When I was a sophomore in college, I had an amazing professor for Physics II: Electricity and Magnetism. He made a series of complex topics fun to learn, and his personality and way of teaching were almost tailor-made for the way I like to learn. He explained new concepts through practical examples, and always kept students engaged throughout the class, making sure everyone understood the lectures. Physics II was an engineering prerequisite, and I didn’t mind taking the class since I really enjoyed the material. However, I did find myself wondering a few times, “Will I ever use any physics in real life?” It turns out that the answer to the question was yes.

The Test Connection: Spreading the Word About DFT

12/07/2022 | Andy Shaughnessy, PCB Design007
As signal speeds continue to increase and feature sizes decrease, PCB designers are beginning to pay greater attention to test and design for test (DFT) strategies. Bert Horner, president of The Test Connection in Hunt Valley, Maryland, is spearheading this drive to show designers the benefits of a solid DFT plan, as well as the downside of not having a test strategy. I met with Bert at PCB Carolina, where he was exhibiting and presenting a paper during the conference. We discussed his presentation, as well as why designers need to understand test and DFT issues, and why we need to see the PCB as one small—but very important—part of the entire system.

DownStream Flexes in Rigid-Flex

11/14/2022 | Andy Shaughnessy, Design007 Magazine
During PCB West, I caught up with DownStream Technologies co-founder Joe Clark and Senior Product Marketing Manager Mark Gallant. We discussed some of their latest tool updates, including a greater focus on bringing post-processing functionality, such as inter-layer analysis capability, to rigid-flex circuits. Joe also offered a look at global design trends going into 2023, as more engineers take on PCB designer roles while senior designers are retiring.



Copyright © 2022 I-Connect007 | IPC Publishing Group Inc. All rights reserved.