Designing a Manufacturable Flexible PCB Involves Tradeoffs


Reading time ( words)

Designers are always inquiring about the limits of flexible PCBs. Maximum amperage, copper thickness, flex life, and minimum recommended pitch are just a few examples of the limits that designers are exploring when designing electronic packages. Design guides and websites provide information and tools related to many of these questions, and materials and properties pages provide information on the various materials and material thicknesses that are typically used. A trace width calculator can give you power, resistance and amperage calculations based on trace configuration. Design guides can also provide information and recommendations on a wide variety of flexible circuit options and characteristics.

In most cases, these information sources address the single criteria, but in reality, a flex designer is faced with multiple requirements that can make calculations and specifications much more complicated. For example, 5 oz. copper may adequately address an amperage requirement, but flexibility can be diminished. Five-ounce copper may not work for high flex applications, although it may work with limited flexing such as flex-to-install applications. Another limitation of thicker copper is the ability to resolve narrow conductors. Circuits with 0.005” width and spacings are commonly fabricated, but with much thinner copper. Five-ounce copper is 0.007” thick. This would require etching ratios (the rate of X-Y etch to Z etch) that present manufacturability issues. So the limits of line width and spacing are highly dependent on copper thicknesses.

Copper thickness and pitch are just two examples of the interdependencies that different characteristics or parameters impose on each other. As flexible circuit features and characteristics such as layer count, number of components, surface finishing and circuit size increase, the interdependencies of multiple criteria become far more complex. As with most things in life, in order to get something you probably have to give something. What is at stake is the manufacturability, and cost effectiveness, of the design. Failure to adequately account for these interdependencies can result in unacceptable manufacturing yields and/or designs that are not robust.

An electronic designer is usually faced with a set of trade-offs when deciding what type of interconnect medium to adopt. Rigid printed circuit boards, connectors, flex circuits, wire harnesses and hand assembly all compete for the attention of a system designer. Often the designer is forced to compromise among several design constraints driven by restrictions that alternative component specifications place on the package. Within flex circuitry design alternatives, the solution may involve going from single-sided to double-sided circuits, adding a shielding layer, folding an “origami” flex circuit, or blending two circuits into one.

Understanding these interdependencies requires a high level of experience and expertise—and sometimes a sequence of trial and error. Many times an iterative process is required even for some of the most experienced flexible circuit engineers. Getting a flexible circuit supplier involved early and often in the design process will eliminate some of the more obvious design issues. Choosing a supplier with a short product start-up cycle time can also be advantageous.

When choosing a flex circuit supplier, look for one with website tools and resources that provide design support with these complex issues. Utilize the engineering talent at the supplier by taking advantage of a design consultation. A robust design review process helps bring a new part number from concept to high volume manufacturing. Designing a flexible circuit doesn’t have to be complicated and challenging if support resources from the supplier are engaged early in the decision process.

Dave Becker is vice president of sales and marketing at All Flex Flexible Circuits LLC.

 

Share




Suggested Items

Book Excerpt: 'The Printed Circuit Designer's Guide to... Manufacturing Driven Design,' Chapter 4

09/12/2023 | I-Connect007 Editorial Team
In Chapter 4 of 'The Printed Circuit Designer's Guide to... Manufacturing Driven Design,' the author, Max Clark, explores industry advancements that bridge the gap between concurrent and intelligent DFM. Both systems complement each other within the typical workflow and represent the beginnings of a transition away from a classical DFM, allowing for an improved NPI process.

Challenges in Modern PCB Design and Analysis

09/05/2023 | Steve Watt, Zuken
Zuken recognizes the need to address innovation in all areas of the design process while remaining responsive to customer-driven requirements. While we can make predictions about various challenges, concerns, and requirements, our customers play a vital role in shaping the company’s development direction. They have the benefit of being “in the trenches,” so to speak, on a daily basis, so they are the subject matter experts and can help identify gaps in our tools based on where their processes are heading.

PCB Design, Digital Twin, and Digital Transformation

08/31/2023 | I-Connect007 Editorial Team
There’s been a lot of talk lately about digital twin and its use in PCB fabrication and assembly. Manufacturers have been quick to get onboard the digital twin train. But what about PCB designers and design engineers? Can the front-end folks benefit from digital twin? We asked David Wiens, Xpedition product manager for Siemens Digital Industries Software, to weigh in on this topic. He’s been involved with digital twin for years, and he explained what digital twin can potentially offer to PCB design, and why he believes designers have been using digital twin for decades, whether they realize it or not.



Copyright © 2023 I-Connect007 | IPC Publishing Group Inc. All rights reserved.