The Top 10 Ways Designers Can Increase Profits


Reading time ( words)

Some of you are probably wondering about the title of this article. “What could Mark possibly mean? How can a lowly PCB designer like me increase our company’s profits?”

So can you truly increase profitability through PCB design practices? Yes, you can. And it starts with a philosophy that embraces DFM techniques. Then you must be ready for the initial release to a fabricator by  ensuring  that you are communicating all of your specifications and needs clearly to the fabrication house so that you get an accurate quote.

Let’s dive in, starting with Number 10 and working our way to the most important way a designer can increase company profits.

10. Accurate Fab Notes

I cannot over-stress this one. Lets talk about some common fab notes that can cause confusion, sometimes delaying your quote.

For instance, do copper weights refer to starting or finished weight? A standard note may read, “All copper weights listed on the stack-up detail are finished weights.”  But a glance at the provided stack-up shows both 1 oz. inners and outers.

Remember, the first fab note specified FINISHED weights. This is not a problem for an internal layer, as they are “print and etch” for the most part. Their desired copper features are protected by the photosensitive resist and are simply printed, developed (to remove the resist not hardened by the light source), etched (to remove the unwanted metal) and resist stripped to remove the resist covering your desired copper features. So a 1 oz. callout for an inner layer is not at all uncommon.

The 1 oz. finish for the outer layers, however, is a bit unusual, given the fact that IPC recommends a minimum of 8/10 of a mil of plated copper on the surface and in the barrel of the hole for continuity. So starting on .5 oz. or even .25 oz. copper foils would mean we would have to plate less than what IPC recommends to finish at 1 oz.

The reality is that most fabricators err towards a full ounce or 1.4 mils of plating in the barrel and on the surface to meet that IPC minimum. That means starting on .25 oz. copper foil on the outers and plating up a full ounce results in 1.25 oz finish, which does not meet the drawing callout of 1 oz finished.

Worse yet, there may be impedance calculations that the customer has based on the 1 oz. finish for outer layers. Increasing the finished copper weight  may mean a REDUCTION in your impedance lines. If you have already taken them down to .003” for instance, this may be a problem for the manufacturer.

This clarification about what is needed for desired copper can take additional time at the quote process. I am happy to say we are seeing more and more customers, both old and new, embracing this and creating non-conflicting manufacturing notes that allow for a 1 oz. additional plate.

To read this entire article, which appeared in the March issue of The PCB Design Magazine, click here.

Share




Suggested Items

Advanced Packaging Means Advanced Routing Issues

01/26/2023 | Kris Moyer, IPC
In today’s ever-shrinking world of electronics designs, the use of BGA parts with very fine pitch features is becoming more prevalent. As these fine-pitch BGAs continue to increase in complexity and user I/O (number of balls), the difficulty of finding escape routes and fan-out patterns increases. Additionally, with the shrinking of silicon geometry leading to both smaller channel length and increased signal integrity issues, some of the traditional BGA escape routing techniques will require a revisit and/or adjustment to allow for not only successful fan-out, but also successful functioning of the circuitry of the BGA design.

Everyone Wants Change: Who Wants to Lead the Way?

01/25/2023 | Nolan Johnson, I-Connect007
Nolan Johnson recently met with Alun Morgan, technology ambassador at Ventec, and Ventec COO Mark Goodwin to discusses the industry’s determination to cling to outdated processes and standards, and some potential consequences. To maintain efficiency and keep pace with the market’s newest entries in Asia, Alun and Mark believe that legacy companies in the West must be open to challenging conversations that will require questioning old practices and revising those practices toward sustainability.

The Battle of the Boards

01/12/2023 | Patrick Crawford, IPC
Last year, IPC held its first-ever design competition at IPC APEX EXPO in San Diego. PCB designers from around the world competed in a series of heats during the months before the show, culminating in a showdown on the show floor between the top three finalists. Rafal Przeslawski, now with AMD, took home the top prize last year. This year, the competition is back for its sophomore year. I asked Patrick Crawford, manager of design standards and related programs for IPC, to “layout” the details on the design contest, including lessons learned in 2022 and what’s new for the 2023 competition.



Copyright © 2023 I-Connect007 | IPC Publishing Group Inc. All rights reserved.